{{item.currency}} {{pricing}}





{{item.currency}}{{pricing}} {{item.currency}} {{item.normalPrice}}



{{item.currency}} {{pricing}} - Out of Stock

Applies to:

 Machine Operators.

Objective:

It is to provide the systematic procedure on how to operate and wash the ice cream machine.

Policy or Handbook Reference

Refer to owner’s manual.

Pre-Requisites

Prior to use, inspect machine and electrical cords for visible damage.

 

Introduction

The main aim of this report is to provide the systematic procedure on how to handle, operate and wash the soft ice cream machine

Definition and term references 

  1. Handles – Used for lifting and moving the machine

  2. Indicator Light – Shows hardness level as well as production process.

  3. Trial running – To test if the machine is properly working

  4. On/Off Switch – Stop command for washing/production.

  5. Setting – For hardness level.

  6. Reset – Validate the restart before the automatic move.

  7. Hopper – means funnel-shaped receptacle

 

Completing the work effort for the ice cream machine

Step

Instruction

Illustration

Expected Result

 

Installation and testing guide

 

 

1

Use the handles on the sides to lift the machine and make sure is always upright.

 

2

Before the electricity connection of the machine, make sure the machine is grounded properly.   

 

 

3

The distance from the machine to the wall must be at least 200mm to the closest wall to prevent over-heating. It is better to leave no less than 500mm from the ventilation side.

 

 

 

4

Plug in the machine cable and switch on the plug

 

 

5

On/Off indicator turns red

It shows that the machine is plugged.

6

Before ice cream production, a trial running is necessary to ensure everything is in good condition.

 

 

7

Long press the On/Off button for few seconds until the indicator lights green.

 

Machine switch on showing that it is ready for use.

8

Within one-minute press stop, button (ON/OFF) to stop the machine. The trial running time is not allowed to be more than 3 minutes.    

 

 

 

 

Ice Cream production

 

 

9

Pour the ready ice cream mix into the two hoppers. Turn the air outlet open to make the feeding into action until the chilling cylinder is filled.

 

10

After pouring enough ice cream mix and adjusting the air outlet well, cover the hopper

 

11

Let the ice cream mix free to flow deeply for 2 minutes and then press the ON/OFF button.

 

The whole machine will go into production mode and ice cream can be finished in 3 to 8 minutes, which varies from models.

12

Draw down the handles on the throat block to dispense

 

The middle outlet is applicable to both of the chilling cylinder and thus it dispenses a mixed flavor of ice cream.

 

 

Cleaning guide

 

 

13

Remember to clean the soft ice cream machine and its parts after using it.

 

 

14

Water temperature used during cleaning should never exceed 40⁰ C since it may cause damage to the plastic parts and seal the machine.

Water must be look warm/must not burn you when you feel by hand.

 

 

15

To prepare sanitizing solution

  1. Fill a 5L container with water.

  2. Pour one bag of sanitizing solution into the water.

  3. Mix the solution for 2 minutes or until all the sanitizer is dissolved.

  4. Pour the solution into the machine hopper. 

 

 

16 a

Sanitize and clean the hoppers and the cooling cylinders.

 

 

16 b

Sanitize and clean the throat block

  1. Disassembly the throat block by loosening off the plastic/stainless still screws

  2.  Take out the beater shafts from the cylinder by pulling & slight rotating.

  3. Put the assembly into detergent or water and clean it one by one to get rid of any dirt.

The assembly will be free of dirt.

17

Assembly the beater shafts and the throat block properly.

 

 

18

Pour water into the hopper

 

 

16

Press the wash button.

 

The beater runs strongly for self-cleaning

16 a

After few minutes, press the wash button to turn off the beater and then take out the throat block slowly to pour out miry water.  

 

 

17

Clean the machine shell with a cloth drenched in a sanitizer.

 

 

18

Clean the drip tray with water and sanitizer

 

 

19

Let the machine dry, then cover the machine and put to storage.

 

 

 

 

Troubleshooting guide

 

 

20

Leakage off ice cream or water

  1. Leakage from the throat block (Change gaskets or sealing)

  2. Leakage from gearbox (Mount the screw in proper position and tighten up.

 

 

21

The ice cream cannot be discharged

  1. The beater shaft does not rotate (Repair or change the damaged parts)

  2. The ice cream is too hard. (Use the ready to use ice cream from a good supplier or adjust the proportion of recipe)

 

 

 

 

Safety Instructions

 

 

22

  1. Always follow the instructions given by the supplier.

  2. If the power cable should of any reason be damaged, a skilled technician with sufficient knowledge and skill should immediately replace it.

  3. Keep close attention to the material (ice cream) capacity in the hopper. Make sure the hopper will never be empty otherwise, consecutive production would cause noise and even damage to then beater.

  4. Avoid any damage to the power cable when transporting the soft ice cream machine. Bending the cable may cause a fire. Never place heavy objects on the power cable.

 

 

 

Expected results

This will keep the soft ice cream machine in a good condition.

Exceptions and escalation

  1. When using the ready-to-use ice cream mixes which goes with stipulated proportion mixing water, do not try to add more water or sugar, since this may lower the quality the product or disturb the operating condition of the machine.

  2. Always remember to sanitize the machine after it has been used, and always keep a strict hygiene.

  3. Always follow the instructions given by the supplier.